ASME B16.5 ASTM A182 SS 316L Plate Ring Flange Raised Face 600LB 24″

Standard ASME B16.5
Size range: DN600 (24")
Pressure range: 600 LB (Class 600)
Material: F316L (UNS S31603)
Flange Facing Types: Raised Face (RF)
Used in: Oil, Offshore, Water, Ship, Natural Gas, Power, Pipe Projects etc

PRODUCT DETAIL

Type: 316L Plate Ring Flange
Material: F316L (UNS S31603)
Size: DN600 (24″)
Standard: ASME B16.5
Pressure Class: 600 LB (Class 600)
Ends: Raised Face (RF)

Chemical Composition and Mechanical Property for 316L
Steel Grade	Chemical Composition									Mechanical Performance
	C(Max)	Si(Max)	Mn(Max)	P(Max)	S(Max)	Ni	Cr	N(Max)	Mo	Tensile Strength (Min)	Yield Strength (Min)
										Mpa	Mpa
316L	0.03	0.75	2.00	0.045	0.03	10.0–14.0	16.0–18.0	0.1	2.00–3.00	485	170

ANSI/ ASME B16.5 Plate Ring Flange Raised Face

ANSI, ASME, ASA, B16.5 150lb/sq.in. Plate Ring Flange RF
ø	D	b	g	m	J	k	Holes	l	Kg.
1/2″	88,9	11,1	34,9	30,2	22,3	60,3	4	15,9	0,400
3/4″	98,4	12,7	42,9	38,1	27,7	69,8	4	15,9	0,700
1″	107,9	14,3	50,8	49,2	34,5	79,4	4	15,9	0,800
1 1/4″	117,5	15,9	63,5	58,8	43,2	88,9	4	15,9	1,100
1 1/2″	127,0	17,5	73,0	65,1	49,5	98,4	4	15,9	1,400
2″	152,4	19,0	92,1	77,8	62,0	120,6	4	19,0	2,200
2 1/2″	177,8	22,2	104,8	90,5	74,7	139,7	4	19,0	3,600
3″	190,5	23,8	127,0	107,9	90,7	152,4	4	19,0	4,100
3 1/2″	215,9	23,8	139,7	122,2	103,4	177,8	8	19,0	5,200
4″	228,6	23,8	157,2	134,9	116,1	190,5	8	19,0	5,600
5″	254,0	23,8	185,7	163,6	143,8	215,9	8	22,2	6,300
6″	279,4	25,4	215,9	192,1	170,7	241,3	8	22,2	7,500
8″	342,9	28,6	269,9	246,1	221,5	298,4	8	22,2	12,600
10″	406,4	30,2	323,8	304,8	276,3	361,9	12	25,4	18,500
12″	482,6	31,7	381,0	365,1	327,1	431,8	12	25,5	28,000
14″	533,4	34,9	412,7	400,0	359,1	476,2	12	28,6	36,000
16″	596,9	36,5	469,9	457,2	410,5	539,7	16	28,6	46,000
18″	635,0	39,7	533,4	504,8	461,8	577,8	16	31,7	50,000
20″	698,5	42,9	584,2	558,8	513,1	635,0	20	31,7	64,000
22″	749,3	46,0	641,2	609,6	564,4	692,1	20	34,9	72,000
24″	812,8	47,6	692,1	663,6	615,9	749,3	20	34,9	89,000

NOTE:

1. Class 150 flanges except Lap Joint will be furnished with 0.06 (1.6mm) raised face, which is included in ‘Thickness’ (C) and ‘Length through Hub’ (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer’s option.

ANSI, ASME, ASA, B16.5 300lb/sq.in. Plain flange/Plate Flange RF
ø	D	b	g	m	J	k	Holes	l	Kg.
1/2″	95,6	14,3	34,9	38,1	22,3	66,7	4	15,9	0,700
3/4″	117,5	15,9	42,9	47,6	27,7	82,5	4	19,0	1,100
1″	123,8	17,5	50,8	54,0	34,5	88,9	4	19,0	1,400
1 1/4″	133,3	19,0	63,5	63,5	43,2	98,4	4	19,0	1,800
1 1/2″	155,6	20,6	73,0	69,8	49,5	114,3	4	22,2	2,600
2″	165,1	22,2	92,1	84,1	62,0	127,0	8	19,0	3,400
2 1/2″	190,5	25,4	104,8	100,0	74,7	149,2	8	22,2	4,400
3″	209,5	28,6	127,0	117,5	90,7	168,3	8	22,2	6,100
3 1/2″	228,6	30,2	139,7	133,3	103,4	184,1	8	22,2	7,500
4″	254,0	31,7	157,2	146,0	116,1	200,0	8	22,2	10,100
5″	279,4	34,9	185,7	177,8	143,8	234,9	8	22,2	12,500
6″	317,5	36,5	215,9	206,4	170,7	269,9	12	22,2	14,100
8″	381,0	41,3	269,9	260,3	221,5	330,2	12	25,4	24,800
10″	444,5	47,6	323,8	320,7	276,3	387,3	16	28,6	37,100
12″	520,7	50,8	381,0	374,6	327,1	450,8	16	31,7	50,000
14″	584,2	54,0	412,7	425,4	359,1	514,3	20	31,7	70,000
16″	647,7	57,1	469,9	482,6	410,5	571,5	20	34,9	90,000
18″	711,2	60,3	533,4	533,4	461,8	628,6	24	34,9	112,000
20″	774,7	63,5	584,2	584,2	513,1	685,8	24	34,9	133,000
22″	838,2	66,7	641,2	641,2	564,4	742,9	24	41,3	197,000
24″	914,4	69,8	692,1	701,7	615,9	812,8	24	41,3	208,000

NOTE:

1. Class 300 flanges except Lap Joint will be furnished with 0.06 (1.6mm) raised face, which is included in ‘Thickness’ (C) and ‘Length through Hub’ (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer’s option.

ANSI, ASME, ASA, B16.5 600lb/sq.in. Plate Flange RF
ø	D	b	g	m	J	k	Holes	l	Kg.
1/2″	95,2	14,3	34,9	38,1	22,3	66,7	4	15,9	0,800
3/4″	117,5	15,9	42,9	47,6	27,7	82,5	4	19,0	1,400
1″	123,8	17,5	50,8	54,0	34,5	88,9	4	19,0	1,600
1 1/4″	133,3	20,6	63,5	63,5	43,2	98,4	4	19,0	2,100
1 1/2″	155,6	22,2	73,0	69,8	49,5	114,3	4	22,2	3,100
2″	165,1	25,4	92,1	84,1	62,0	127,0	8	19,0	3,700
2 1/2″	190,5	28,6	104,8	100,0	74,7	149,2	8	22,2	5,400
3″	209,5	31,7	127,0	117,5	90,7	168,3	8	22,2	7,300
3 1/2″	228,6	34,9	139,7	133,3	103,4	184,1	8	25,4	8,900
4″	273,0	38,1	157,2	152,4	116,1	215,9	8	25,4	11,800
5″	330,2	44,4	185,7	188,9	143,8	266,7	8	28,6	24,500
6″	355,6	47,6	215,9	222,2	170,7	292,1	12	28,6	29,500
8″	419,1	55,6	269,9	273,0	221,5	349,2	12	31,7	43,000
10″	508,0	63,5	323,8	342,8	276,3	431,8	16	34,9	70,000
12″	558,8	66,7	381,0	400,0	327,1	488,9	20	34,9	86,000
14″	603,2	69,8	412,7	431,8	359,1	527,0	20	38,1	100,000
16″	685,8	76,2	469,9	495,3	410,5	603,2	20	41,3	142,000
18″	742,9	82,5	533,4	546,1	461,8	654,0	20	44,4	175,000
20″	812,8	88,9	584,2	609,6	513,1	723,9	24	44,4	232,000
22″	869,9	95,2	641,2	666,7	564,4	777,9	24	47,6	292,000
24″	939,8	101,6	692,1	717,5	615,9	838,2	24	50,8	330,000

NOTE:
1. Class 600 flanges except Lap Joint will be furnished with 0.25 (6.35mm) raised face, which is not included in ‘Thickness’ (C) and ‘Length through Hub’ (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Dimensions of sizes 1/2 through 3 1/2 are the same as for Class 400 Flanges.
6. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer’s option.

Application

Bicycle and automobile exhaust tubing, cooling pipe, Electroplating equipment, precision instruments, ring, environmental protection equipment
Thermal power engineering:condenser, heat exchanger, engine vane
Vessels:Running pipes, submersible, gas cylinder
Oceaneering: evaporator, heat transmitter, exchanger, oil production platform, oil cooler
Chemical engineering:Flat plate heat exchanger, flat plate condenser, cooler tower, chloride barrels
Aerospace:Engine, fan plate, gas compressor vane, rack, hatch cover, empennage